China MIG-250amp 110V Fully Automatic Welding Machine - High-Quality TIG & MMA Welding from Reliable Suppliers and Factory
Product Parameters
| Rated Input Voltage | 1P 230V+_15% |
| Actual useable current | 20-250A |
| Rated Frequency | 50/60hz |
| No-load voltage(V) | 68 |
| Rated duty cycle(40℃) | 60% |
| Input capacity(KVA) | 4.7 |
| Perfect usable welding wire/rod | 1.6-4.0 |
| Visible cable | 1.5m |
| Holder/Clamp | 200A |
| Machine Meas. | 28*13*22cm |
| Weight (KG) | 5.8KG |
| Motor Type | DC MOTOR |
| Protection Degree | IP21S |
| Type | IGBT 1PCB |
| Packaging Details | color box+foam |
Product Display
Product introduction and use
How to use the product
-
1
Check the wire delivery wheel, first put down the button, lift the pressure wheel, and remove the shell. The wire feeding wheel inside has two slots, 0.8 and 1.0. Install 1.0 welding wire, put 1.0 faces out, install 0.8 welding wire, and 0.8 faces out.
-
2
Put the welding wire into the wire tray and remove the screws. Take down the parts inside, put the welding wire down, put the welding wire tray, and don't put the welding wire up. After putting it out, put the partition first, then put the spring, and then put the iron sheet in place. Finally, take the screw and screw it three times. Don't tighten it too much, so that the wire plate can be fully moved. Next, straighten the welding wire, pass the welding wire from the bottom, pass through the wire feeding wheel, and then pass the welding wire backwards. After the welding wire comes out from the front, press the pressure wheel, lift the button, and the welding wire installation is completed.
-
3
Take out the welding gun and put the welding wire through the welding. In the middle of the gun, put on the welding gun and twist it, and then connect the switch cable above. Next, install the ground wire, adjust the function to MIG, buckle the welding torch switch, and start to rotate the welding wire. When the welding wire is sent to the muzzle, the welding wire comes out.
-
4
Put on the ground wire, pick up the welding gun, put the welding wire in the middle, and pull the trigger to weld.
-
5
MMA can also be used, and spot welding can be used. The function can be switched to MMA with one click, and the manual welding handle can be used. 3.2 welding rods and 2.5 welding rods can be used, and spot welding can be used. You can also use TIG, and the function can switch to TIG with one click.
Frequently Asked Questions
What welding modes are supported by this machine?
This welding machine supports three major modes: MMA (Manual Metal Arc) welding, MIG (Metal Inert Gas) welding, and TIG (Tungsten Inert Gas) welding.
What sizes of welding wires and rods can I use?
The machine is compatible with 1.6-4.0 welding rods (including 2.5 and 3.2 rods for manual welding) and 0.8 to 1.0 welding wires.
How do I adjust the wire feeding wheel for 0.8 or 1.0 welding wire?
The wire feeding wheel features two slots: 0.8 and 1.0. To use 1.0 welding wire, install the wheel with the 1.0 side facing out. For 0.8 welding wire, install it with the 0.8 side facing out.
Can this machine weld aluminum and stainless steel?
Yes, the MIG and TIG processes are suitable for welding various materials, including carbon steel, stainless steel, and aluminum.
What are the electrical parameters and duty cycle of this welder?
The welder has a rated input voltage of 1P 230V ±15%, an actual usable current range of 20-250A, and a rated duty cycle of 60% at 40℃.
How do I switch the machine functions?
You can switch functions easily. The machine allows you to switch between MMA, TIG, or MIG modes with one click.